Practices by Discipline

PIP produces broadly applicable code-compliant practices.

Browse PIP Practices

Review the most up-to-date collection of PIP Practices. Most recently published practices are listed first. Search key terms or filter by discipline to narrow the list.

Found 606 Results

Piping

PNE00012

Piping Examination and Leak Test Guide

Abstract ↓

This Practice provides guidelines for specifying the requirements for examination and leak testing of metallic, lined metallic, and nonmetallic piping systems designed in accordance with ASME B31.3 Process Piping, hereinafter referred to as the Code. The requirements include examination of piping materials, components, fabrication, assembly, installation, and associated documentation. This Practice also covers the extent of examination, criteria for acceptance, and correction of defective work. It describes the types of leak tests, bases for selecting the appropriate tests, and arrangements for testing piping.

December 2023
Complete Revision

Piping

PNC00005

Design of ASME B31.3 Metallic Piping Systems

Abstract ↓

This Practice provides requirements for designing metallic piping systems to ASME B31.3, Process Piping (hereinafter referred to as the Code). This Practice provides requirements for piping systems arrangement, design conditions, components, and joints. This Practice shall be used in conjunction with the Code. The requirements of this Practice are more stringent than the Code for the purpose of standardization and not because the Code is considered unsafe. Piping systems designed in accordance with other piping codes are not included in this Practice.

September 2023
Complete Revision

Data Management

ADG011

Requirements for Awarding Professional Development Hours

Abstract ↓

This Practice provides the minimum requirements and policies regarding professional development hours (PDHs) issued by Process Industry Practices (PIP) for Professional Engineering licensees (PEs) participating in Continuing Education Programs (CEPs), to the extent required by respective state boards of licensure. PIP does not issue Continuing Education Units (CEUs).

September 2023
Technical Revision

I/E

ELSAP01

Design and Fabrication of Utility Type Battery Chargers

Abstract ↓

This Practice describes the minimum requirements for design, fabrication, inspection, testing, shipment, and documentation for an electronically-controlled battery charger used for charging float-type batteries and simultaneously powering the connected utility system loads in indoor unclassified areas. This Practice does not apply to grounded DC systems.

September 2023
Technical Revision

I/E

ELCGL01

Electrical Design Criteria

Abstract ↓

This Practice describes the general design requirements and basis of design for electrical systems. This Practice includes requirements for system components and typical configurations.

August 2023
Technical Revision

Piping

PN03CB2J01

Piping Material Specification 3CB2J01,Class 300 Killed Carbon Steel Jacketed Pipe

Abstract ↓

Not applicable

August 2023
New Practice

Data Management

ADG010

Specification for Numbering Practices

Abstract ↓

This Practice describes the PIP Practice numbering system and requirements for each field.

August 2023
Technical Revision

Piping

PN01CB2J01

Piping Material Specification 1CB2J01, Class 150 Killed Carbon Steel Jacketed Pipe

Abstract ↓

Not applicable

August 2023
New Practice

Process

PHSREM001

Specification for Mixers, Blenders and Agitators used in Hygienic Applications (Universally Applicable)

Abstract ↓

This Practice describes the minimum requirements for permanently mounted, top-, bottom-, and side-entering mixers and agitators installed in pressurized or unpressurized vessels, with or without mechanical seals. This Practice does not cover requirements for portable and clamp-on light duty mixers or agitators, in-line mixers, jet-type mixers, or high-speed dispersers. The requirements in this Practice are modifications, additions, and/or deletions (exceptions) to the requirements in PIP RESM003 – Specification for Mixers and Agitators. The section/paragraph numbers and the associated headings used in this Practice correspond to the ones used in PIP RESM003. Because this Practice does not take exception to all the requirements in PIP RESM003, the section/paragraph numbers in this Practice may not be sequential.

August 2023
New Practice

Mechanical

RFSF1000

Ceramic Fiber Refractory Material Specification (Universally Applicable)

Abstract ↓

This Practice describes the requirements for the certification and prequalification of ceramic fiber refractory materials used to construct refractory linings in fired heaters and other process equipment. It provides a basis for selection, purchase, and quality control of ceramic fiber refractory materials. Included are material property, testing, documentation, storage, packaging, and marking requirements for the following types of ceramic fiber refractories: a. Alkaline Earth Silicate (AES) b. Refractory Ceramic Fiber (RCF) c. Polycrystalline Wool (PCW) This Practice does not include mineral wool, fiberglass, and other non-refractory fiber insulations, or rigid block refractory insulation materials.

July 2023
Reaffirmation

Mechanical

RESP002

Design of ASME B73.1 and General Purpose Pump Baseplates (Universally Applicable)

Abstract ↓

This Practice provides the minimum requirements for ASME B73.1 pump baseplates and baseplates for general purpose pumps. This Practice describes minimum requirements for horizontal pump baseplates that are not covered in the API standards.

July 2023
Complete Revision

Mechanical

RESP005D

Data Sheet for Sealless Centrifugal Pumps

Abstract ↓

Not applicable - Data Sheet only Practice

June 2023
Technical Revision

I/E

ELSAP20

Low-Voltage Automatic Transfer Switch

Abstract ↓

This Practice describes the requirements for the design, fabrication, inspection, testing, and shipping of factory-assembled low-voltage automatic transfer switches. This Practice does not cover fast transfer systems.

June 2023
Complete Revision

Data Management

ADG004

Specification for Developing CAD Graphics for Practices

Abstract ↓

This Practice provides requirements and work process for ensuring consistency of style and presentation for Computer-Aided Drafting (CAD) associated with Process Industry Practices (Practices). This Practice provides detailed instructions for the Function/Task Team representative and CAD representative. This Practice does not apply to figures inserted in the narrative of a Practice.

June 2023
Complete Revision

CSA

STE05121

Application of ASCE Anchorage Design for Petrochemical and Other Industrial Facilities

Abstract ↓

This Practice provides guidelines for design engineers involved in design, fabrication, installation, and repair of anchorage for foundations and structures. This Practice supplements the ASCE Anchorage Design for Petrochemical and Other Industrial Facilities, hereafter referred to as the ASCE Anchorage Design Report. The information on fabrication, installation, and repair of anchorages provided in this Practice is to be used by design engineers to develop specifications, drawings, scopes of work, etc. for fabricators, constructors, and maintenance personnel involved in fabrication, installation, and repair activities.

May 2023
Complete Revision

Piping

PN01SA0J01

Piping Material Specification 1SA0J01 Class 150, 304/304L Stainless Steel, Jacketed Construction, C.A.- None, Core: Process Jacket: Steam

Abstract ↓

Not applicable

May 2023
Complete Revision

Piping

PN01SD0J01

Piping Material Specification 1SD0J01 Class 150, 316/316L Stainless Steel, Jacketed Construction, C.A. – None, Core: Process Jacket: Steam

Abstract ↓

Not applicable

May 2023
Complete Revision

Piping

PN03SA0J01

Piping Material Specification 3SA0J01 Class 300, 304/304L Stainless Steel, Jacketed Construction, C.A. – None, Core: Process Jacket: Steam

Abstract ↓

Not applicable

May 2023
Complete Revision

Piping

PN03SD0J01

Piping Material Specification 3SD0J01 Class 300, 316/316L Stainless Steel, Jacketed Construction, C.A. – None, Core: Process Jacket: Steam

Abstract ↓

Not applicable

May 2023
Complete Revision

Piping

PN09SA0S01

Piping Material Specification 9SA0S01 Class 900, 304/304L Stainless Steel, Socket Weld, C.A.- None, Process

Abstract ↓

Not applicable

May 2023
Complete Revision

Date not available
Update type not available

Page 17 of 31

Learn More About PIP Practices

X/Twitter

This field is for validation purposes and should be left unchanged.

Name(Required)

First Name Last Name

Company Name(Required)

Work Email Address(Required)

Select the document(s) you’d like to download.(Required)

PIP ADG001 - Specification for Developing Practices

PIP ADG010 - Specification for Numbering Practices

PIP ADG012 - Guideline for Adoption and Implementation of PIP Practices